Sedona Plumbing and Heating installs gas, oil, and propane furnaces in Arlington, MA homes from our Winchester shop. Our trucks reach most Arlington addresses 10-15 minutes from dispatch. We are an authorized Rheem installer, EPA 608 certified for refrigerant handling, and a registered Mass Save installer. We size every furnace to your home’s actual heat load, not square-footage rules of thumb.
Furnace Installation in Arlington, MA
Arlington’s mix of triple-deckers along Mass Ave and single-family homes up the hill toward Lexington means we see a wide range of equipment ages. Older Arlington homes regularly need full replacements rather than band-aid repairs. For furnace installs specifically, the typical Arlington call comes when an existing 80% AFUE furnace is 20+ years old and either showing failure signs (short-cycling, uneven heat, gas-smell complaints, ignitor failures) or just costing too much to keep running. We install replacement furnaces in 1-2 days, including any duct modifications, gas line resizing, venting upgrades, and full system commissioning.
Furnace Types We Install
High-efficiency condensing gas furnaces (95%+ AFUE): Two-stage and modulating units from Rheem, Carrier, and Trane. Significantly lower operating cost than older 80% AFUE units. Eligible for Mass Save rebates.
Standard 80% AFUE furnaces: For homes where condensing-furnace venting is impractical or where the budget calls for a simpler swap. Still a major efficiency improvement over a 60% AFUE 1980s furnace.
Oil and propane furnaces: For Arlington homes without natural gas service. Becket and Rheem oil furnaces, propane configurations from major manufacturers.
Dual-fuel and hybrid systems: Heat pump primary heat with gas furnace backup for the coldest days. Best of both worlds — heat pump efficiency at moderate temps, furnace capacity in deep cold.
What’s Included in Furnace Installation
Pulling and disposing of the old furnace. Installing the new unit. Updating gas line sizing if needed (a high-efficiency furnace often needs a different gas line than what the old unit used). New venting (PVC for condensing, B-vent for standard 80%). New thermostat or smart thermostat if you want one. Pulling all required permits. Coordinating duct modifications with our HVAC team if your existing ductwork is undersized.
Mass Save Rebates and Financing
Arlington homeowners qualify for Mass Save rebates on high-efficiency furnaces and especially on heat pump conversions. We are a registered Mass Save installer and handle the rebate paperwork. Mass Save 0% HEAT Loan financing is available for qualifying upgrades.
Why Choose Sedona for Furnace Installation in Arlington
Local dispatch from Winchester. 10-15 minutes from our shop to most Arlington addresses.
EPA 608 certified for HVAC work. Veteran-owned, fully insured, registered Mass Save installer.
Right-sized installs. We perform a heat-loss calculation as part of the estimate. An oversized furnace short-cycles and wastes fuel; an undersized furnace cannot keep up.
Upfront flat-rate pricing. Detailed written quote before work starts.
24/7 emergency response in Arlington. No-heat in January gets immediate dispatch.
Areas We Serve Near Arlington
Beyond Arlington, we install furnaces in Winchester, Medford, Cambridge, Somerville, Belmont and surrounding communities.
Frequently Asked Questions about Furnace Installation in Arlington
How long does furnace installation in Arlington take?
Most furnace replacements take 1-2 working days, including pulling the old unit, installing the new furnace, gas and venting updates, and commissioning. Larger duct modifications can extend the timeline.
Should I switch from a furnace to a heat pump?
Often worth considering. Mass Save heat pump rebates of up to $10,000 plus 0% HEAT Loan financing make the conversion math compelling, and operating costs are typically lower than oil or propane. We will run the comparison numbers at the in-home estimate.
What size furnace does my Arlington home need?
It depends on your home’s heat loss, not square footage. We perform a heat-loss calculation to size the furnace correctly. Oversizing is the most common installation mistake and the easiest way to ruin a new furnace’s lifespan.
Can you install a smart thermostat with my new furnace?
Yes. We install Ecobee, Honeywell, and Aprilaire smart thermostats with new furnace installs. The right thermostat pairs the furnace controls with your schedule and HVAC zoning.
Need furnace installation in Arlington, MA? Call (781) 242-2386 or use the form on this page.
Other Services in Arlington
- Furnace Repair in Arlington
- Central AC Installation in Arlington
- Heat Pump Installation in Arlington
- Boiler Installation in Arlington
- Ductless Mini-Split Installation in Arlington
- All plumbing services in Arlington
