Sedona Plumbing and Heating installs residential boilers in Newton, MA homes from our Winchester shop. Our trucks reach most Newton addresses 20-25 minutes from dispatch. We are a Massachusetts Master Plumber licensed and Mass Save registered installer, and we install high-efficiency gas, oil, and propane boilers from Lochinvar, Burnham, Weil-McLain, Navien, and Buderus.
Boiler Installation in Newton, MA
Newton’s 13 villages range from historic Newton Centre estates to mid-century Newton Highlands single-family. Equipment ranges from large boilers serving 6,000 sq ft homes to standard residential systems. When it comes to boiler replacement, the typical Newton call is a 50+ year old cast-iron boiler running at 60-70% efficiency that has finally given out — or a homeowner planning ahead before the next no-heat winter morning. We replace residential boilers in 1-2 days for most installations, including all venting, controls, near-boiler piping, and code-compliance work.
Boiler Types We Install
High-efficiency gas boilers (95%+ AFUE): Modulating-condensing units from Lochinvar, Weil-McLain, and Burnham. Eligible for Mass Save rebates and dramatic operating-cost reduction vs older cast-iron units. We size each unit to your home’s actual heat loss, not a rule of thumb.
Combi (combination) boilers: One unit for both space heating and domestic hot water. Navien, Lochinvar, and Weil-McLain combi units. Ideal when you are replacing both an old boiler and an old water heater at the same time, especially in tight Newton mechanical rooms where a separate water heater would not fit.
Cast-iron and steel sectional boilers: Traditional non-condensing boilers for homes where condensing venting is not practical or homeowners want longer service life. Burnham and Weil-McLain residential models.
Steam boilers: For Newton homes still on original cast-iron radiator steam systems. Burnham, Weil-McLain, and Lochinvar steam boilers, sized to the connected radiator load.
Oil and propane boilers: For Newton homes without natural gas service. Buderus, Burnham, Weil-McLain. We also handle oil-to-gas and oil-to-heat-pump conversions.
What’s Included in Boiler Installation
Pulling and disposing of the old boiler. Installing the new unit per manufacturer specs. New near-boiler piping (typically copper or PEX). New venting (stainless or PVC for condensing units, B-vent for non-condensing). New controls and zone management. Pressure-testing the system. Pulling all required permits and coordinating inspection. A full system commissioning before we leave.
Mass Save Rebates and Financing
Newton homeowners qualify for Mass Save rebates on high-efficiency gas boilers and substantial rebates on heat pump conversions if you are open to electrifying. We are a registered Mass Save installer and handle the rebate paperwork as part of the install. Mass Save 0% HEAT Loan financing is available.
Why Choose Sedona for Boiler Installation in Newton
Local dispatch from Winchester. 20-25 minutes from our shop to most Newton addresses.
Master Plumber licensed gas fitters. Veteran-owned, fully insured, EPA 608 certified, registered Mass Save Heat Pump installer.
Detailed heat-loss sizing. We size every boiler to your home’s actual heat loss, not square footage rules of thumb. Right-sized boilers run quieter, last longer, and operate more efficiently.
Upfront flat-rate pricing. Detailed written quote before work starts.
24/7 emergency response in Newton. When the boiler fails on a January morning, we move fast.
Areas We Serve Near Newton
Beyond Newton, we install boilers in Waltham, Watertown, Belmont, Weston, Cambridge and surrounding communities.
Frequently Asked Questions about Boiler Installation in Newton
How long does boiler installation in Newton take?
Most boiler replacements take 1-2 working days, including pulling the old unit, installing the new boiler, near-boiler piping, venting, controls, and commissioning. More complex retrofits (steam-to-modern, fuel conversions) can take 3 days.
Should I replace my Newton boiler with a heat pump instead?
Often worth considering. Mass Save heat pump rebates of up to $10,000 plus 0% HEAT Loan financing make whole-home conversions affordable, and operating costs are typically lower than oil or propane. We will run the comparison numbers at the in-home estimate.
Can I keep my existing radiators if I replace the boiler?
Yes. Whether you have cast-iron radiators, baseboard, or radiant tubing, the new boiler connects to your existing distribution system. Cast-iron radiators in particular pair perfectly with modern high-efficiency boilers.
What size boiler does my Newton home need?
It depends on heat loss, not square footage. We perform a heat-loss calculation as part of the estimate to size the boiler correctly. Oversized boilers cycle constantly and waste fuel; undersized boilers cannot keep up on the coldest days.
Need boiler installation in Newton, MA? Call (781) 214-8685 or use the form on this page.
Other Services in Newton
- Boiler Repair in Newton
- Furnace Installation in Newton
- Heat Pump Installation in Newton
- Water Heater Installation in Newton
- Tankless Water Heater Installation in Newton
- All plumbing services in Newton
